Home >> Products
Search by Product
Search by Application
Product List
This product is no longer available.
PrintGuidelines on Printing Website Material

No.5623 Double-faced Film Tape (For Rubber)

Slion Tape No.5623 is a double-faced adhesive tape with polyester film used for the base material, and with a rubber based adhesive applied to one surface and a synthetic resin-based adhesive applied to the other surface. Slion Tape No. 562300 exhibits outstanding adhesion (one surface) to vulcanized rubber which is difficult to bond as an adherend. Slion Tape No.5623 can be used for fixing vulcanized rubber, etc.

Tape structure
No.5623 Double-faced Film Tape (For Rubber)

Applications

Fixing, etc. of vulcanized rubber (EPDM, etc.)

Tape Performance
Test item Surface Unit Value Test method
Thickness - mm 0.105 In conformance with JIS Z 0237
Adhesion For SUS plate (stainless steel) 1 N/10 mm 9.8
2 6.1
For PE plate (polyethylene) 1 6.0
For EPDM rubber plate
(Ethylene-propylene-diene rubber)		 8.6
For NR rubber plate (natural rubber) 7.8
For CR rubber plate (chloroprene) 4.1
For fluoro rubber 4.1
For butyl rubber 5.8
For urethane rubber 1.6
For SBR foam
(styrene butadiene rubber)		 3.9
For NR foam (natural rubber) 0.6
For EP foam (ethylene propylene) 1.4
Holding power at 40°C 1 Deviation: mm/after 24 hours 0.0
2 0.1

* The measured values shown here are reference values only, and are not intended to serve as guaranteed values.
* The specifications of the product maybe changed without prior notice.
* Characteristics may vary in accordance with the adherend material and surface conditions. In the event that any plasticizer is contained in rubber, this may migrate to the tape side. Conduct thorough tests before use.

Standard Dimensions and Units Per Package
Size (width × length) Content per carton
25mm × 50m 40 rolls
30mm × 50m 32 rolls
80mm × 50m 12 rolls
110mm × 50m 12 rolls
1020mm × 50m 1 roll
1050mm × 50m 1 roll

Please consult us for other sizes.
Note) Quantities contained may be changed without prior notice.

Directions for use
(1)
Sufficient adhesive strength may not be obtained if the surface this tape is being applied to is dirty. Remove any dirt, dust, moisture, and oil, etc. before applying this tape.
(2)
In order to obtain sufficient adhesion, apply sufficient pressure in order to bond this tape after it is affixed.
(3)
Store this tape in a cool place, avoiding heat sources such as direct sunlight and heating equipment.
(4)
Do not use for electrical insulation as this is not insulation tape.
(5)
Do not directly apply this tape to furniture, walls, glass, vinyl chloride products, and car bodies, etc. as this may result in adhesive deposits, discoloration or peeling of paint.
(6)
This tape is not designed for application to the skin. Do not directly apply to the skin as this may result in a rash or adhesive deposits.
(7)
) This tape is not designed to hold heavy loads. Use for fixing paper, film, and other light loads.
(8)
Depending upon the type of material to which this product is to be applied, this tape may leave adhesive residues or contaminate the adherent. Check well before use.
(9)
Please check that this tape suits your application before use.
(10)
Contact us when using this tape for special applications.
(TEL: 0120-147-224)
(11)
Take care when using this tape as Sliontec will not be held liable for damage occurring as a result of using this tape.
5623060502
PrintGuidelines on Printing Website Material
 
Back to List
Top of this page